Each pack includes 12 phillips truss heads, 12 Open Slotted Post Fasteners, Knife Sheaths, and 12 Rubber Washers/Spacers. Easy to tighten - the open slotted fasteners are ideal because they allow for a tighter and more secure connection than non-slotted fasteners. The included washers are resistant to liquids and oils and are able to withstand extreme temperatures.
100% satisfaction guaranteed - we take great pride in our products and make sure that the highest quality standards are met by sending each product through a rigorous inspection procedure. Dimensions - phillips screw heads have a 3/8" outside diameter and 1/4" long threaded section with an 8-32 thread, Slotted Post Fasteners have a 7/16" outside diameter and 1/4" long threaded section, Rubber Washers have a 1/2" outside diameter.
In the extremely unlikely occurrence that you are not fully satisfied with the product, we offer a 100% money back guarantee. We are confident that you will be happy with your purchase and we stand by our product. Strong & durable - each piece of hardware is made of high carbon steel and coated with a high tech black thermochemical treating to harden it and give it a gun-like matte finish that eliminates any glare.
Strong & durable - each piece of hardware is made of high carbon steel and coated with a high tech black thermochemical treating to harden it and give it a gun-like matte finish that eliminates any glare.
Tandy Leather Eyelet Setter w/Anvil 1/4" 8095-00
0.080" Thick, Black, 8" x 12", 2 Pack - Plastics 2000 - KYDEX Sheet
. Forming guidelines - oven temperatures should be set differently than the settings used for ABS or FR-ABS. Kydex kydex sheet has excellent forming properties, which results in uniform wall thicknesses and crisp detail. The most frequent problem is trying to heat the sheet too quickly, particularly on the primary surface.
Typical heater settings percentage timers are 30% - 50% top heaters and 50% - 70% bottom heaters. When forming kydex sheet, it is better to rely on the sheet appearance during heating than on fixed cycle times. Stage iv: the ripples will have smoothed out indicating that most stresses have been removed. 196 - 204°c 385 - 400°f for > 3.
20mm 0125" - ideally the core sheet temperature should be within 10°F of the surface temperature.
Holster Clip 1.5" 5 Pk
Industry Standard Hole Spacing. Among the most rigid of thermoforming materials with a modulus of elasticity of 2, 482 MPa 360, 000 psi. Quick clip style for 1. 5" belts. Perfect blend of Function and Style.
Mil-Spec Kydex Eyelets GS 8-8, Brass Black Oxide 1/4" DIY Gun Holster Knife Sheath Grommets 100
205" total thickness. Specifications: ✔ 100, 200, 500 & 1, 000 count packages ✔ Size Specs for GS 8-8 0.288" overall Length x 0384" face width x 0245" length under Flange x 0246" diameter ✔ material: solid brass ✔ finish: mil-spec MIL-DTL-13924 Black Oxide Finish ✔ For installation in 0250" - 1/4" diameter holes ✔ Materials up to.
205" total thickness ✔ 1-Year No-B. S. Gs 8-8 brass eyelets for installation in 0250" - 1/4" holes. Made in the usa: solid brass Eyelets with Military Spec Black Oxide Finish. These are not the shiny black you will see others selling these are FLAT BLACK. Easy to form with excellent part definition and deep-draw characteristics.
KYDEX Sheet - 0.080" Thick, Black, 8" x 12", 4 Pack - Plastics 2000
Cycle times will vary depending on the oven conditions and grade of KYDEX sheet being formed. Higher breakage resistance than competitive thermoplastics as measured by the Notched Izod test. Made in USA. Forming guidelines - oven temperatures should be set differently than the settings used for ABS or FR-ABS.
165 - 177°c 330 - 350°f for < 1. 50mm 0060". Quick clip style for 1. 5" belts. Tough polymer Resin Withstand Daily Use. 196 - 204°c 385 - 400°f for > 3. 20mm 0125" - ideally the core sheet temperature should be within 10°F of the surface temperature.
Plastics 2000 - KYDEX Sheet - 0.080" Thick, Black, 12" x 12", 4 Pack
165 - 177°c 330 - 350°f for < 1. 50mm 0060". Kydex sheet forms to deep draws with low forces when heated to the upper end of the forming temperature range. Perfect blend of Function and Style. Gs 8-8 brass eyelets for installation in 0250" - 1/4" holes. Great for knife sheaths and gun holsters. Mil-spec mil-dtl-13924 flat Black Oxide Finish.
Stage ii: the material will start to form small ripples known as oil canning. Forming guidelines - oven temperatures should be set differently than the settings used for ABS or FR-ABS. Forming temperatures - guidelines: Sheet should not exceed 204°C 400°F. Higher breakage resistance than competitive thermoplastics as measured by the Notched Izod test.
Among the most rigid of thermoforming materials with a modulus of elasticity of 2, 482 MPa 360, 000 psi.
KYDEX Sheet - 0.080" Thick, Black, 12" x 12", 2 Pack - Plastics 2000
Typical heater settings percentage timers are 30% - 50% top heaters and 50% - 70% bottom heaters. Higher breakage resistance than competitive thermoplastics as measured by the Notched Izod test. Higher breakage resistance than competitive thermoplastics as measured by the Notched Izod test. Great for knife sheaths and gun holsters.
Forming guidelines - oven temperatures should be set differently than the settings used for ABS or FR-ABS. Among the most rigid of thermoforming materials with a modulus of elasticity of 2, 482 MPa 360, 000 psi. Great for knife sheaths and gun holsters. Stage i: the heating is marked by wide undulations and softening.
Higher breakage resistance than competitive thermoplastics as measured by the Notched Izod test.
Kydex Holster Belt Quick Clips for IWB/OWB Sheath/Gun Holster Making with Replacement Hardware 1.5" or 1.75"- Slotted Binding Posts/Chicago Screws. Made in USA 1.5" 2-Pack
135" ✔ 1-year No-B. S. Join leather, kydex, boltaron & Other Materials up to. 205" total thickness. All made in usa! - Lifetime NO-B. S warranty. Tough polymer Resin Withstand Daily Use. Among the most rigid of thermoforming materials with a modulus of elasticity of 2, 482 MPa 360, 000 psi. Great for knife sheaths and gun holsters.
Hardware included - 2 per clip; black 8-32 x 1/4" Screws & Slotted Binding Posts & Washers. Higher breakage resistance than competitive thermoplastics as measured by the Notched Izod test. Made in USA. Easy to form with excellent part definition and deep-draw characteristics.
Quick Clip Pro Holster Tough Grip Clips, 3 Hole Adjustable Cant for IWB OWB Kydex, Leather, Hybrid Holster Making. Tuckable Black Plastic w/Chicago Screw Hardware Made in USA 1.5" 2-Pack
Higher breakage resistance than competitive thermoplastics as measured by the Notched Izod test. Pros choice - strong, durable - Same Clips Used By Majority Of Professional Holster Makers. Easy to form with excellent part definition and deep-draw characteristics. Perfect blend of Function and Style. Great for knife sheaths and gun holsters.
Includes hardware-black oxide screws & open back Chicago Screw Posts & Washers All of our clips are Made in USA, they include a Lifetime -No-B. S. The professionals Choice, Made in the USA. Made in USA. Among the most rigid of thermoforming materials with a modulus of elasticity of 2, 482 MPa 360, 000 psi. Among the most rigid of thermoforming materials with a modulus of elasticity of 2, 482 MPa 360, 000 psi.
0.080" Thick, Black, 12" x 12" Nominal, 8PACK - KYDEX V Sheet
Made in USA. Quick clip style for 1. 5" belts. 10 to 30 seconds afterwards the sheet is ready to form. Stage ii: the material will start to form small ripples known as oil canning. Hardware - set of 2 per clip; black oxide 8-32x1/4" Phillips screws & binding posts & washers. Sheet appearance during heating As KYDEX V sheet is heated, the inherent stresses in the sheet will relax.
Higher breakage resistance than competitive thermoplastics as measured by the Notched Izod test. Among the most rigid of thermoforming materials with a modulus of elasticity of 2, 482 MPa 360, 000 psi. Kydex v sheet forms to deep draws with low forces when heated to the upper end of the forming temperature range.
Made in USA. Great for knife sheaths and gun holsters. Forming temperatures - guidelines: Sheet should not exceed 204°C 400°F.